Nortel Networks 10BASE-T Bedienungsanleitung Seite 229
- Seite / 330
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Using the Console Interface
309985-C Rev 00
3-87
LEC Status
Allows you to enable or disable the selected LEC.
Default Disable
Range Disable, Enable
LEC State
This read-only field displays the current status of the selected LEC.
Default Disabled
Range Disabled, Idle, Operational, Unknown
ELAN Name
Allows you to enter a name for the ELAN that is associated with the selected LEC.
You should also verify that the ELAN you are connecting to exists on the target ATM
switch.
Default default
Range Any ASCII string of up to 20 printable characters
VLAN
This read-only field displays the current VLAN that is associated with the selected
LEC. The default configuration for the LEC is 0 (no VLAN assigned).
You can assign a LEC to any currently active port-based VLAN. Use the VLAN
Configuration screen to assign the appropriate VPort number for the LEC to a VLAN.
Default 0
Range 1 - 4094
LEC VPort
This read-only field displays the LEC VPort (virtual port) number that is associated
with the selected LEC. This VPort number is also shown on other CI screens (such
as the VLAN Configuration screen or the Spanning Tree Configuration screen, as
appropriate).
Default 13 / 25
The four LECs are assigned VPort numbers that directly relate to
the switch version (12 port or 24 port) where they are installed. For
example, when installed in a 24-port switch, LECs 1, 2, 3, and 4
are assigned as VPorts 25, 26, 27, and 28 respectively.
Range (12-port models) = 13,14,15,16 / (24-port models) = 25,26,27,28
Desired Physical
Port
Allows you to configure the physical port (A1 or A2) for the selected LEC.
Default A1
Range A1, A2
(continued)
Table 3-32. LEC Configuration Screen Fields
(continued)
Field Description
- Using the BayStack 410-24T 1
- 10BASE-T Switch 1
- Trademarks 2
- Statement of Conditions 2
- USA Requirements Only 2
- European Requirements Only 2
- Taiwan Requirements 3
- Canada Requirements Only 3
- Contents 7
- 309985-C Rev 00 10
- Audience 24
- Organization 24
- Text Conventions 25
- Acronyms 26
- Related Publications 28
- How to Get Help 29
- Chapter 1 31
- Front Panel 32
- 410-24T Switch 34
- Back Panel 36
- Features 39
- Security 43
- IEEE 802.1p 46
- IGMP Snooping Feature 47
- Flash Memory Storage 47
- Configuration Parameters 48
- MultiLink Trunking 49
- IEEE 802.1Q VLANs 49
- Port Mirroring 49
- SNMP MIB Support 51
- SNMP Trap Support 51
- Network Configuration 52
- Segment Switch Application 54
- CPU PS1 PS2FAN 55
- Fail-Safe Stack Application 56
- Stack Operation 57
- Cascade A Out 59
- Cascade A In 59
- Unit Select 59
- Cascade A InUnit Select 60
- Base Unit 61
- Stack Configurations 63
- IEEE 802.1Q VLAN Workgroups 68
- IEEE 802.1Q Tagging 69
- Shared Servers 76
- (Port Name is 80
- VLAN Workgroup Summary 81
- VLAN Configuration Rules 83
- IGMP Snooping 84
- IEEE 802.1p Prioritizing 89
- MultiLink Trunks 93
- Before Configuring Trunks 105
- 400-4FX MDA 107
- Chapter 2 119
- Figure 2-1. Package Contents 120
- Installation Procedure 121
- Caution: 122
- Comm Port 129
- Connecting Power 130
- Cascade Module 131
- 100-240V 131
- 47-63Hz~ 131
- Redundant Power 131
- Verifying the Installation 132
- Initial Setup 135
- Stack Setup 138
- Chapter 3 143
- Using the Console Interface 143
- Main Menu 146
- IP Configuration/Setup 150
- Choosing a BootP Request Mode 152
- BootP Disabled 153
- BootP or Last Address 153
- BootP When Needed 154
- BootP Always 154
- SNMP Configuration 155
- System Characteristics 157
- Switch Configuration 160
- MAC Address Table 163
- MAC Address-Based Security 165
- and 3-11) 170
- Configuration screen 171
- Screen 1 174
- Screen 2 174
- Screen 3 174
- Screen 4 174
- Screen 5 174
- Screen 16 178
- VLAN Configuration Menu 181
- Table 3-12 describes the 182
- Table 3-14 187
- Table 3-15. Reserved PIDs 188
- Port Configuration 195
- Table 3-19 describes the 196
- MultiLink Trunk Configuration 200
- Table 3-21 describes the 201
- Table 3-23 describes the 206
- Port Mirroring Configuration 207
- Table 3-24 describes the 208
- Table 3-25. Monitoring Modes 210
- Rate Limiting Configuration 211
- IGMP Configuration Menu 214
- Table 3-29 describes the 220
- Port Statistics 221
- ATM Configuration Menu 225
- Renumber Stack Units 243
- Hardware Unit Information 245
- Spanning Tree Configuration 245
- Software Download 256
- Download screen 257
- Configuration File 260
- Display Event Log 263
- Excessive Bad Entries 264
- Write Threshold 265
- Flash Update 265
- Save Current Settings 266
- Reset to Default Settings 269
- Chapter 4 273
- Troubleshooting 273
- Interpreting the LEDs 274
- Warning: 276
- Normal Power-Up Sequence 277
- Port Connection Problems 278
- Software Download Error Codes 280
- Appendix A 283
- Technical Specifications 283
- Physical Dimensions 284
- Performance Specifications 284
- Data Rate 285
- Interface Options 285
- Safety Agency Certification 285
- Electromagnetic Emissions 285
- Electromagnetic Immunity 286
- Declaration of Conformity 286
- Appendix B 287
- Media Dependent Adapters 287
- 400-4TX MDA 288
- 100BASE-FX MDAs 289
- 400-2FX MDA 290
- Installing an MDA 292
- Replacing an MDA 293
- Appendix C 295
- Quick Steps to Features 295
- Configuring 802.1Q VLANs 296
- Off-page reference 297
- On-page reference 297
- Configuring MultiLink Trunks 302
- Configuring Port Mirroring 303
- Configuring IGMP Snooping 305
- Appendix D 309
- MDI and MDI-X Devices 310
- Appendix E 315
- Default Settings 315
- Appendix F 323
Verwandte Produkte und Handbücher für Vernetzung Nortel Networks 10BASE-T
Vernetzung Nortel Networks 24T Bedienungsanleitung
(310 Seiten)
(310 Seiten)
(86 Seiten)
Vernetzung Nortel Networks 5100 Bedienungsanleitung
(160 Seiten)
(160 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern