Nortel Networks 24T Bedienungsanleitung Seite 276
- Seite / 310
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Using the BayStack 410-24T 10BASE-T Switch
B-6
309985-B Rev 00
Installing an MDA
The Uplink Module slot on the BayStack 450 switches accommodates a single
MDA. The connection can be either a 10/100BASE-TX MDA with an RJ-45
connector or a (fiber) 100BASE-FX MDA with an SC or MT-RJ connector.
To install an MDA into the Uplink Module slot:
1.
Unplug the AC power cord from the back of the switch.
2.
Loosen the thumb screws and remove the filler panel (or previously
installed MDA) from the Uplink Module slot.
3.
Insert the MDA into the Uplink Module slot guides (Figure B-3).
Make sure the MDA slides in on the guides provided. Failure to align the
guides could result in bent and broken pins
Figure B-3. Installing an MDA
4.
Press the MDA
firmly
into the Uplink Module slot.
Be sure that the MDA is fully seated into the mating connector.
5.
Secure the MDA by tightening the thumb screws on the MDA front panel.
Note:
The MDA is not hot-swappable. Power down the switch before
installing or removing an MDA.
Note:
If you are replacing an installed MDA with another type of MDA, see
“
Replacing an MDA with a Different Model” on page B-7.
BS41048A
- Using the BayStack 410-24T 1
- 10BASE-T Switch 1
- Trademarks 2
- Statement of Conditions 2
- USA Requirements Only 2
- European Requirements Only 2
- Taiwan Requirements 3
- Canada Requirements Only 3
- Contents 7
- 309985-B Rev 00 10
- Before You Begin 24
- Organization 24
- Text Conventions 25
- Acronyms 26
- Related Publications 27
- How to Get Help 28
- Chapter 1 29
- Front Panel 30
- 410-24T Switch 32
- Back Panel 34
- Features 37
- Security 41
- RADIUS-Based Network Security 43
- IEEE 802.1p 44
- IGMP Snooping Feature 44
- Flash Memory Storage 45
- MultiLink Trunking 46
- IEEE 802.1Q VLANs 47
- Port Mirroring 47
- 00-00-82-99-44-00 48
- 00-00-82-99-44-1F 48
- SNMP MIB Support 49
- SNMP Trap Support 49
- Network Configuration 50
- Segment Switch Application 52
- CPU PS1 PS2FAN 53
- Fail-Safe Stack Application 54
- Stack Operation 55
- BS41010A 56
- Base Unit 57
- Stack Configurations 59
- BS41011A 60
- IEEE 802.1Q VLAN Workgroups 64
- IEEE 802.1Q Tagging 65
- Shared Servers 72
- (Port Name is 76
- VLAN Workgroup Summary 77
- VLAN Configuration Rules 79
- IGMP Snooping 80
- IEEE 802.1p Prioritizing 85
- MultiLink Trunks 89
- Before Configuring Trunks 101
- 400-4FX MDA 103
- Chapter 2 115
- Figure 2-1. Package Contents 116
- Installation Procedure 117
- Caution: 118
- Connecting Power 126
- Cascade Module 127
- 100-240V 127
- 47-63Hz~ 127
- Redundant Power 127
- Verifying the Installation 128
- Initial Setup 131
- Figure 2-13. Main Menu 132
- Stack Setup 134
- Chapter 3 139
- Using the Console Interface 139
- Main Menu 142
- IP Configuration/Setup 146
- Choosing a BootP Request Mode 148
- BootP Disabled 149
- BootP or Last Address 149
- BootP When Needed 150
- BootP Always 150
- SNMP Configuration 151
- System Characteristics 153
- Switch Configuration 156
- MAC Address Table 158
- MAC Address-Based Security 160
- Screen 1 169
- Screen 2 169
- Screen 3 169
- Screen 4 169
- Screen 5 169
- Screen 16 173
- VLAN Configuration Menu 176
- Table 3-12 describes the 177
- Table 3-14 182
- Table 3-15. Reserved PIDs 183
- Port Configuration 190
- Table 3-19 describes the 191
- MultiLink Trunk Configuration 195
- Table 3-23 describes the 201
- Port Mirroring Configuration 202
- Table 3-24 describes the 203
- Table 3-25. Monitoring Modes 205
- Rate Limiting Configuration 206
- IGMP Configuration Menu 209
- Table 3-29 describes the 215
- Port Statistics 216
- Renumber Stack Units 227
- Hardware Unit Information 229
- Spanning Tree Configuration 229
- TELNET Configuration 237
- Software Download 240
- Download screen 241
- Configuration File 244
- Display Event Log 247
- Excessive Bad Entries 248
- Write Threshold 248
- Flash Update 249
- Reset to Default Settings 252
- Chapter 4 257
- Troubleshooting 257
- Interpreting the LEDs 258
- Warning: 260
- Normal Power-Up Sequence 261
- Port Connection Problems 262
- Software Download Error Codes 264
- Appendix A 267
- Technical Specifications 267
- Physical Dimensions 268
- Performance Specifications 268
- Data Rate 269
- Interface Options 269
- Safety Agency Certification 269
- Electromagnetic Emissions 269
- Electromagnetic Immunity 270
- Declaration of Conformity 270
- Appendix B 271
- Media Dependent Adapters 271
- 400-4TX MDA 272
- 100BASE-FX MDAs 273
- 400-2FX MDA 274
- Installing an MDA 276
- Appendix C 279
- Quick Steps to Features 279
- Off-page reference 280
- On-page reference 280
- Appendix D 289
- MDI and MDI-X Devices 290
- Appendix E 295
- Default Settings 295
- Appendix F 303
Verwandte Produkte und Handbücher für Vernetzung Nortel Networks 24T
(86 Seiten)
Vernetzung Nortel Networks 5100 Bedienungsanleitung
(160 Seiten)
(160 Seiten)
Vernetzung Nortel Networks M3820 Bedienungsanleitung
(264 Seiten)
(264 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern