Nortel Networks 24T Bedienungsanleitung Seite 55
- Seite / 310
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Introduction to the BayStack 410-24T Switch
309985-B Rev 00
1-27
Stack Operation
BayStack 410-24T switches provide fail-safe stacking when you install the
optional BayStack 400-ST1 Cascade Module (see “
Fail-Safe Stack Application”
on page 1-26
). You can connect up to eight switches to provide uninterrupted
connectivity for up to 224 ports. The entire stack is manageable as a single unit.
Installation instructions are provided with the BayStack 400-ST1 Cascade Module
(see your Nortel Networks sales representative for ordering information).
BayStack 400-ST1 Cascade Module
The front panel components of the BayStack 400-ST1 Cascade Module are shown
in Figure 1-10
.
Component descriptions follow the figure.
Figure 1-10. BayStack 400-ST1 Front Panel Components
Cascade A Out
Cascade A In
Unit Select
Base
1 = Blank connectors (unused)
2 = Cascade A Out connector
3 = Unit Select switch
4 = Cascade A In connector
3
BS41009A
4
1
2
- Using the BayStack 410-24T 1
- 10BASE-T Switch 1
- Trademarks 2
- Statement of Conditions 2
- USA Requirements Only 2
- European Requirements Only 2
- Taiwan Requirements 3
- Canada Requirements Only 3
- Contents 7
- 309985-B Rev 00 10
- Before You Begin 24
- Organization 24
- Text Conventions 25
- Acronyms 26
- Related Publications 27
- How to Get Help 28
- Chapter 1 29
- Front Panel 30
- 410-24T Switch 32
- Back Panel 34
- Features 37
- Security 41
- RADIUS-Based Network Security 43
- IEEE 802.1p 44
- IGMP Snooping Feature 44
- Flash Memory Storage 45
- MultiLink Trunking 46
- IEEE 802.1Q VLANs 47
- Port Mirroring 47
- 00-00-82-99-44-00 48
- 00-00-82-99-44-1F 48
- SNMP MIB Support 49
- SNMP Trap Support 49
- Network Configuration 50
- Segment Switch Application 52
- CPU PS1 PS2FAN 53
- Fail-Safe Stack Application 54
- Stack Operation 55
- BS41010A 56
- Base Unit 57
- Stack Configurations 59
- BS41011A 60
- IEEE 802.1Q VLAN Workgroups 64
- IEEE 802.1Q Tagging 65
- Shared Servers 72
- (Port Name is 76
- VLAN Workgroup Summary 77
- VLAN Configuration Rules 79
- IGMP Snooping 80
- IEEE 802.1p Prioritizing 85
- MultiLink Trunks 89
- Before Configuring Trunks 101
- 400-4FX MDA 103
- Chapter 2 115
- Figure 2-1. Package Contents 116
- Installation Procedure 117
- Caution: 118
- Connecting Power 126
- Cascade Module 127
- 100-240V 127
- 47-63Hz~ 127
- Redundant Power 127
- Verifying the Installation 128
- Initial Setup 131
- Figure 2-13. Main Menu 132
- Stack Setup 134
- Chapter 3 139
- Using the Console Interface 139
- Main Menu 142
- IP Configuration/Setup 146
- Choosing a BootP Request Mode 148
- BootP Disabled 149
- BootP or Last Address 149
- BootP When Needed 150
- BootP Always 150
- SNMP Configuration 151
- System Characteristics 153
- Switch Configuration 156
- MAC Address Table 158
- MAC Address-Based Security 160
- Screen 1 169
- Screen 2 169
- Screen 3 169
- Screen 4 169
- Screen 5 169
- Screen 16 173
- VLAN Configuration Menu 176
- Table 3-12 describes the 177
- Table 3-14 182
- Table 3-15. Reserved PIDs 183
- Port Configuration 190
- Table 3-19 describes the 191
- MultiLink Trunk Configuration 195
- Table 3-23 describes the 201
- Port Mirroring Configuration 202
- Table 3-24 describes the 203
- Table 3-25. Monitoring Modes 205
- Rate Limiting Configuration 206
- IGMP Configuration Menu 209
- Table 3-29 describes the 215
- Port Statistics 216
- Renumber Stack Units 227
- Hardware Unit Information 229
- Spanning Tree Configuration 229
- TELNET Configuration 237
- Software Download 240
- Download screen 241
- Configuration File 244
- Display Event Log 247
- Excessive Bad Entries 248
- Write Threshold 248
- Flash Update 249
- Reset to Default Settings 252
- Chapter 4 257
- Troubleshooting 257
- Interpreting the LEDs 258
- Warning: 260
- Normal Power-Up Sequence 261
- Port Connection Problems 262
- Software Download Error Codes 264
- Appendix A 267
- Technical Specifications 267
- Physical Dimensions 268
- Performance Specifications 268
- Data Rate 269
- Interface Options 269
- Safety Agency Certification 269
- Electromagnetic Emissions 269
- Electromagnetic Immunity 270
- Declaration of Conformity 270
- Appendix B 271
- Media Dependent Adapters 271
- 400-4TX MDA 272
- 100BASE-FX MDAs 273
- 400-2FX MDA 274
- Installing an MDA 276
- Appendix C 279
- Quick Steps to Features 279
- Off-page reference 280
- On-page reference 280
- Appendix D 289
- MDI and MDI-X Devices 290
- Appendix E 295
- Default Settings 295
- Appendix F 303
Verwandte Produkte und Handbücher für Vernetzung Nortel Networks 24T
(86 Seiten)
Vernetzung Nortel Networks 5100 Bedienungsanleitung
(160 Seiten)
(160 Seiten)
Vernetzung Nortel Networks M3820 Bedienungsanleitung
(264 Seiten)
(264 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.170 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern